Question - How do you replace a clawfoot tub drain?

Answered by: Matthew Carter  |  Category: General  |  Last Updated: 23-06-2022  |  Views: 1022  |  Total Questions: 6

Follow these steps to replace and old, rusty clawfoot tub drain. Step 1 - Shut Off the Main Water Supply. Step 2 - Disconnect the Tub From the Water Supply. Step 3 - Remove the Overflow Plate. Step 4 - Removing the Overflow Pipe. Step 6 - Taking Away the Old Putty. Step 7- Installing the New Piping. Table of Contents Step 1: Remove the Old Tub. Step 2: Prepare the Tub for Reglazing. Step 3: Use Acid-etch Cleaner. Step 4: Degrease the Tub. Step 5: Use Adheser. Step 6: Apply Primer. Step 7: Add Finish Coat. Step 8: Size and Cut Drain Pipe. It's also worth noting that these tubs are often cast-iron and very heavy; you might have to pay to have your floors reinforced before installation. Clawfoot tubs can be a huge pain. If you absolutely love the look and are ready to commit to the upkeep, it might be totally worth it for your home. First, remove the stopper. Insert the Drain Key or the Smart Dumbell into the drain. Keep turning drain counterclockwise until the old drain is released - it shouldn't take too many turns before the drain comes right out. Clean drain area, making sure to remove all old putty residue. Clawfoot tubs are big The appeal of a clawfoot tub is the size. However, the size can be a problem for small bathrooms. A clawfoot tub takes up most of the space in the bathroom leaving little room for much else. While clawfoot tubs add charm to a bathroom, consider a space-saving tub for small bathrooms.

https://www.qualitybath.com/discover/post/16029/clawfoot-tubs-everything-need-know

Typically, a clawfoot tub is generously sized. Ensure that the tub you want will fit through all doors, halls, and stairwells to get into the bathroom, and allow for at least 3-6 inches of space on each side of the tub.

https://www.bostonstandardplumbing.com/blog/5-things-to-know-about-a-clawfoot-tub/

Source and drain lines come through the floor. In a typical clawfoot tub installation, both the water source pipes and the drain pipe enter the bathroom through the floor. Consult with a licensed plumber if you intend to install a clawfoot tub on the second floor of your home!

https://www.doityourself.com/stry/how-to-remove-a-clawfoot-bathtub

How to Remove a Clawfoot Bathtub Step 1 - Close the Water Supply. Shut the water off by locating the water shut off valve and turning it all the way off. Step 2 - Remove Drain Gate. To remove the drain, first remove the drain gate that is located on top of the drain. Step 3 - Remove the Drain. Step 4 - Safety First. Step 5 - Break It Up. Step 6 - Clean Up.

https://terrylove.com/forums/index.php?threads/disabling-overflow-drain.5306/

You could put a piece of Saran Wrap over the whole thing and the water would probably hold it in place after the water rises over it. You might take the overflow mechanism off the tub and try to fit a rubber gasket behind it, with a hole for the drain actuator, to effectively seal the overflow.

https://www.familyhandyman.com/bathroom/shower-installation/how-to-convert-bathtub-drain-lever-to-a-

Grab hold of it and tug hard until it pops out. Screw on the new overflow plate once the linkage has been removed. Unscrew the overflow plate and pull the upper linkage out of the overflow pipe. Pop out the drain stopper and remove the lower linkage as well.

Adding a little shine with the use of a porcelain repair kit will hide the repair. Remove any rust around the hole with the use of a stiff wired brush. Dip a cloth into cold water and clean up any debris left from the brushing. Mix epoxy resin and epoxy hardener in a small pail.