Question - What are the different kinds of dovetail joints?

Answered by: Pamela Wright  |  Category: General  |  Last Updated: 18-06-2022  |  Views: 1286  |  Total Questions: 12

There are 5 different types of dovetail joint methods available. Through Dovetail Joints. Half-blind Dovetail Joints or Single-lap Dovetail. Half blind dovetail vs. Through dovetail. Secret Mitred Dovetail Joints. Secret Double-Lapped Dovetail Joints. Sliding Dovetail Joints. Noted for its resistance to being pulled apart (tensile strength), the dovetail joint is commonly used to join the sides of a drawer to the front. A series of 'pins' cut to extend from the end of one board interlock with a series of 'tails' cut into the end of another board. The pins and tails have a trapezoidal shape. For this test, the box joint proved stronger. Plus, the box joint is strong in both directions, whereas the dovetails are useful only for pulling from one piece, but not the other. So really, to use a dovetail joint for the sake of strength is obsolete, mostly on account of the strength of wood glues. Dovetail joints consist of an interlocking and snugly fitted series of pins and tails. All the tails are cut into one piece of wood, called here the tail piece. The other main category is the “half blind” or “single lap” dovetail. It is called that because the drawer front overlaps the tail ends on the drawer side. The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Dovetail Joints: Different Types and Their Uses Through dovetail. Half-blind dovetail. Secret mitered dovetail. Sliding dovetail. Full-blind dovetail.

https://www.adhesives.org/resources/knowledge-center/aggregate-single/everything-you-need-to-know-ab

Dovetail joints show the care and craftsmanship applied to woodworking projects. A few simple gluing and assembly tips make dovetail joint easier to put together. While the joints are dry, fit the pieces 2/3 to 3/4 of the way into place to ensure that the pieces will fit together.

https://www.wikihow.com/Join-Two-Pieces-of-Wood

Method 1 Making an Edge Joint Arrange your boards and mark them with chalk. Lay the boards across strips of scrap wood. Apply an even bead of glue along the edge of a board. Clamp the boards and ensure they're flush. Wipe away excess glue after 20 minutes. Allow the glue to cure overnight.

https://www.diynetwork.com/how-to/make-and-decorate/decorating/what-to-look-for-when-buying-old-furn

“There's no hard and fast rule, but hand dovetailing was really no longer done in factories after that date, ” Masaschi says. Hand dovetails are slightly irregular and the pins are thin and tapered. Wider, uniform machine-cut dovetails were common in factory-made pieces from 1890 until the modern era.

https://en.wikipedia.org/wiki/Rabbet

A rabbet or rebate is a recess or groove cut into the edge of a piece of machinable material, usually wood. When viewed in cross-section, a rabbet is two-sided and open to the edge or end of the surface into which it is cut. A rabbet can be used to form a joint with another piece of wood (often containing a dado).

https://www.thesprucecrafts.com/determine-the-age-of-antique-furniture-148746

How to Determine the Age of Antique Furniture Look Past the Style of a Piece. When you are trying to determine the age of piece you cannot just look at furniture style. Examine Bottoms, Insides, and Backs. Take a look at the joinery (the spots in furniture where the pieces come together). Check for Perfectly Matching Elements.

https://toolsfirst.com/what-is-dovetail-jig/

A dovetail jig is a tool that make the joining process both quick and easy. Using a dovetail jig effectively involves three pieces: a template, a router, and the bits you're going to join. Using the cutting edge of the router, you follow the template like a stencil to make small, precise cuts in the edge of the wood.

https://www.rockler.com/learn/does-the-angle-of-the-dovetail-affect-the-strength-of-the-joint

Lower (7° to 9°) angles are often advised for joining hardwoods, while higher angles (10° to 14°) are recommended for softwoods and even higher angles (14° to 18°) for half-blind dovetails.

http://m.yspanel.com/news/the-advantages-and-disadvantages-of-the-finger-22413902.html

Finger Joint Wood cons The finger joint wood is not so durable than the other wood like peak wood and need to refinish. after a short period of time. The finger joint wood can damaged by water. because it is not a water- resistance wood, so take good care of it.

https://core.ac.uk/download/pdf/2745198.pdf

Origins The dovetail appears to have originated by at least the Egyptian first dynasty (3000 B. C. ) as it was found in furniture boxes and coffins, as well as in ivory work. clear that the dovetail was also used as a building joint.

https://blog.furniturecart.com/english-and-french-dovetail-drawer-construction/

English Dovetail: Notice the jigsaw cutouts on the sides of each drawer piece, which when joined together form a tightly fit drawer. French Dovetail: This technique is based on cutting out a slat in the middle of a board and also a corresponding piece of wood that can slide into the middle cutout.

https://sawmillcreek.org/showthread.php?23956-Dovetails-in-plywood

Nowadays when I do dovetails, it is only with solid lumber. When plywood drawer sides are called for, there are several non-dovetail joints which work well. A good one is often called "tongue and rabbet". You can make it on a tablesaw, and do it very quickly.